Bitumastic M08 mastic is a waterproofing solution that combines elasticity, durability, and economy. The material contains polymer additives, mineral fillers, and solvents.

Product technical data

Application areas:

• Waterproofing of concrete or wood surfaces. 
• Protection of engineering structures (basements, piles, and other elements of construction).

Consumption:

For one layer is 1 kg/m². Recommended number of layers for installation of surface waterproofing – 2 mastic layers.

Advantages:

• Ready to use
• Can be applied by persons without training or skills
• Suitable for any type of waterproofing or repairs
• Durable and highly elastic product
• Can be used at temperatures below 0°C

Method of application:

Mastic should be applied to prepared surfaces clear of any debris and surplus materials, by using a stiff paint brush, filling knife, or by pouring and leveling. 

Storage:

Store in a dry place protected against sunlight at a temperature between -20°C and +30°C. Shelf life - 18 months. 

Availability

Bitumastic – M08 is available in:

·        Bulk

·        IBC Tank, Flexi Tank

·        Reconditioned steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        New steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        20 Lit pails

12-14 Kg cardboard box

Bitumastic M07 is a multi-component material combining polymer-modified bitumen, fillers, organic solvents, and technological additives. The Bitumastic M07– Cold apply mastic is a fire-free solution to the Pour and Roll application, the cold mastic can be applied in the same way as hot melt application but without hazardous fire melting and hot works permit processes.

Product technical data

Application areas:

Bitumastic M07– Cold-apply mastic is used in traditional built-up waterproofing applications to adhere sand-surfaced rolled membranes to any type of substrate. 

Consumption:

0.8–1.8 kg per 1 m² depending on the base type.

Advantages:

• Ready to use (must be well stirred before application)
• Fire-free traditional pour and roll application
• Provides additional strength to traditional build-up systems
• Gives highly reliable bonding to roofing membranes

Method of application:

The cold applied mastic should be poured onto the surface, then leveled out using a toothed knife or stiff comb. 

Storage:

Store in a dry place protected against sunlight at a temperature between -20°C and +30°C. Shelf life - 18 months. 

Availability

Bitumastic – M07 is available in:

·        Bulk

·        IBC Tank, Flexi Tank

·        Reconditioned steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        New steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        20 Lit pails

Bitumastic® M06 is a liquid rubber, ready-to-use material suitable for repair works or for waterproofing entire roofs and details. The material consists of oil bitumen modified by artificial polymers, mineral fillers, and organic solvents. After drying, the material forms a highly strong and elastic covering, highly resistant to temperature changes, considerably increasing the service life of the protected surfaces. 

Product technical data

Application areas:

• Entire roof waterproofing including details and parapets. 
• Waterproofing of engineering structures (basements, footings, piles, and other building elements buried underground likely to be in contact with a damp environment). 
• Weatherproofing and anti-corrosion treatment of metal surfaces including pipelines and car bodies.

Consumption:

• for mastic roof installation: 3.8–5.7 kg/m²; 
• for waterproofing installation: 2.5–3.5 kg/m².

Advantages:

• Ready to use 
• Tough and highly elastic product 
• Can be used at temperatures below 0°C 
• Significantly prolongs the service life of protected structures

Method of application:

Bitumastic M06 – Roof mastic should be applied to the prepared surface to clear any debris and surplus materials, mastic can be applied by using a stiff paint brush, filling knife, or by pouring and leveling. Single-layer thickness should not exceed 1.5 mm, each subsequent layer must be applied after the previous layer is completely dry. It is highly recommended to apply a minimum of 2 layers, to achieve durable waterproofing. 

Storage:

Store in a dry place protected against sunlight at a temperature between -20°C and +30°C. Shelf life - 18 months. 

Availability

Bitumastic – M06 is available in:

·        Bulk

·        IBC Tank, Flexi Tank

·        Reconditioned steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        New steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        20 Lit pails

·        12-14 Kg cardboard box  

Bitumastic M05 is a hot-applied roofing mastic that is produced of roofing bitumen modified with polymers and mineral filler. Due to the similar composition, the mastic is fully compatible with waterproofing polymer-bitumen membranes. Its application provides a reliable and holistic roofing system. 

Product technical data

Area of application:

 
Hot applied roofing mastic Bitumastic M05 is designed for the installation or repair of roofs (with the sealing of cracks, potholes sand-cement and asphalt screeds, concrete slabs grooves; restoration of roofing; installation of drainage funnel; in junctions of roofing membranes with pipes, aerators; fire-less installation of roofing membranes). Also, it is used for waterproofing steel or concrete structures (including pipelines), concrete blocks, and columns in contact with the ground).

LIMITATIONS

Do not overheat material. Cracks must be free from moisture, dust, loose aggregate and other contaminates before application

Consumption

Actual material usage may vary due to the width of application and thickness of material above pavement surfaces.

Storage

Cracks must be free from moisture, dust, dirt, and debris. Both substrate and air temperature must be above 5°C. Keep boxes of material dry during storage. Do not store in direct sunlight.

Availability

Bitumastic M05 is available in:

·        Bulk

·        IBC Tank, Flexi Tank

·        Reconditioned steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        New steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        20 Lit pails

12-14 Kg cardboard box

Bitumastic M04 - Polymer bitumen mastic sealant is a single component hot applied crack and joint sealant consisting of bitumen modified by artificial rubber and special additives. When melted and properly applied it forms a resilient crack sealant for both asphaltic and cementitious pavements. The sealant has a wide range of operating temperatures, high elasticity, lack of shrinkage, and short curing time. It is produced in three grades: M04-G25, M04-G35, and M04-G50.

Product technical data

Area of application:

·        Expansion joints in concrete and asphalt coatings, sealing of airfields and motor roads.

·        Cracks curing of airfields and motor roads concrete and asphalt coatings

LIMITATIONS

Do not overheat material. Cracks must be free from moisture, dust, loose aggregate and other contaminates before application

Consumption:

Actual material usage may vary due to the width of application and thickness of material above pavement surfaces.

Storage

Cracks must be free from moisture, dust, dirt, and debris. Both substrate and air temperature must be above 5°C. Keep boxes of material dry during storage. Do not store in direct sunlight.

Availability

Bitumastic – M04 is available in:

·        Bulk

·        IBC Tank, Flexi Tank

·        Reconditioned steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        New steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        20 Lit pails

12-14 Kg cardboard box

Bitumastic M03 is a hot-applied rubber-bitumen mastic which is a multi-component compound consisting of bitumen, crumb rubber, and plasticizers. When melted and properly applied, it forms a resilient and adhesive compound for both cement and asphaltic pavements.

Product technical data

Area of application:

·        Waterproofing of underground steel pipelines and other structures to protect against soil corrosion.

·        Sealing joints and cracks in roofing.

·        Installation of roofing bitumen membranes, providing vapor barrier when installing roofing systems.

·        Application under the tram rail. 

·        Waterproofing of building structures.

Method of application

Proper surface preparation facilitates adequate adhesion and consequently the maximum life of the sealant. For proper adhesion, the crack/joint must be free of moisture, dust, loose aggregate, and other contaminants. The substrate and air temperatures must be 40°F or above. Sawing, routing, and/or sandblasting are the preferred methods of preparation. Use oil-free compressed air and heat to clean and dry the surface immediately before sealing. Cracks/joints should be sized so that the maximum extension and compression do not exceed 50% of the width. Best results are obtained when the cracks/joints are opened at least 1.5 Cm wide.

Consumption:

Actual material usage may vary due to the width of application and thickness of material above pavement surfaces.

Storage

Cracks must be free from moisture, dust, dirt, and debris. Both substrate and air temperature must be above 5°C. Keep boxes of material dry during storage. Do not store in direct sunlight.

Availability

Bitumastic – M03 is available in:

·        Bulk

·        IBC Tank, Flexi Tank

·        Reconditioned steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        New steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        20 Lit pails

·        12-14 Kg cardboard box  

Bituprime Waterproof – P02 is an emulsified bitumen base primer produced by a special emulsifier and stabilizer to have good surface coverage and waterproofing performance. It is non-toxic once dried and is ideal for waterproofing flat roofs, gutters, flashings, water reservoirs, and koi ponds.
The product can be cold applied to vertical and horizontal surfaces and once dried; it forms a tough, durable, and flexible waterproof barrier.

Product technical data

Application areas:

Bituprime waterproof is used to prepare the substrate for the application of torch-on, self-adhesive, or other types of waterproofing materials. It’s suitable to prime concrete roofs and floors, cementitious screeds/renders, brickwork, bitumen felt, weathered bitumen, mastic asphalt, weathered, corrugated iron, and steel.

• Waterproofing of flat roofs, parapets, and flashings
• Waterproofing of ponds and water reservoirs
• Sealing of joints between different roofing materials, gutter joints, and roof screws
• Waterproofing and protective coating for below-ground foundations

Limitations:

Do not apply if the temperature is below 5°C

Do not apply to damp surfaces

Bitumen compounds have poor UV resistance and must be over-coated with paint if exposed to sunlight or UV rays. Due to the tendency of bitumen compounds to bleed through and discolor paints applied over them.

Bitumen primer Consumption:

Bituprime Waterproof – P02 consumption per m2 will be 0.25–0.35 l/m² (1 l per 3.33 m²).

Method of application:

Bituprime Waterproof – P02 should be applied to the prepared surface to clear off any debris or sharp projections. Agitate the pails(drum) before use then the primer should be applied in continuous coat using a roll or brush penetrating the surface and providing a smooth and well-adhered base for subsequent waterproofing layers. Apply at temperatures +5°C – +40°C, water can be added if necessary.

Note: Tools and brushes must be cleaned immediately after use with water and soap

Advantages:

• Ready to use 
• Suitable for indoor applications 
• Solvent free, non-flammable 
• Water-based, Environment-friendly
• Cost-efficient, easy to apply

Safety instructions:

Bituprime Waterproof – P02 is non-toxic, however, it is advisable to wear gloves in order to avoid direct skin contact. In the event of skin or eye contact, rinse thoroughly and immediately with water.    Seek medical assistance if irritation or discomfort persists.  Keep out of reach of children!  Refer to our Safety Data Sheets for further toxicological information and comprehensive handling instructions.

Storage:

 Store in a dry place protected against sunlight at a temperature not less than +5°C. Shelf life - 9 months. Ensure the container is closed to create an airtight environment when not in use.

Availability

Bituprime Coating – P02 is available in:

·        Bulk

·        IBC Tank, Flexi Tank

·        Reconditioned steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        New steel drums 220 lit., Net Weight: 200 ± 3 Kg

20 Lit pails

Bituprime Coating - P01 is a bitumen primer that is a suitable solution for single-coat applications and it is usable for all types of substrates. It contains high-quality petroleum bitumen and a special solvent that the softening temperature is not lower than 70°C.  

Product technical data

Application areas:

To achieve strong adhesion of materials to porous, rough, and dusty surfaces, possible to use Bituprime Coating. It’s suitable to prime concrete roofs and floors, cementitious screeds/renders, brickwork, bitumen felt, weathered bitumen, mastic asphalt, weathered, corrugated iron, and steel. for prime concrete roofs and floors, cementitious screeds/renders, brickwork, bitumen felt, weathered bitumen, mastic asphalt

Limitations:

· Not suitable for potable drinking water tanks.

· Bitumen compounds tend to bleed through and discolor paints are subsequently applied over it. Apply a primer recommended by the paint manufacturer before painting.

Bitumen primer Consumption:

Bituprime Coating – P01 consumption per m2 will be 0.25–0.35 l/m² (1 l per 3.33 m²).

Method of application:

Bituprime Coating – P01 should be applied to the prepared surface to clear any debris or sharp projections.

Ensure surfaces are clean, dry, and free of loose materials, dust, grease, rust, and other contaminants.  Defects such as cracks should be repaired before primer application. For metal surfaces (old) remove any flaking material or rust with a wire brush. For previously coated surfaces should completely remove any old paint first then apply the new coating layer.

The bitumen primer should be applied in a continuous coat using a roll or brush penetrating the surface and providing a smooth and well-adhered base for subsequent waterproofing layers.

Advantages:

§  Improves the bond of bituminous materials

§  Binder for dust particles

§  Surface dressing to masonry and metal surfaces

§  Water-resistant.

§  Corrosion and chemical resistance.

§  Penetrates and seals porous surfaces.

§  Fast-drying.

§  Cost-effective, no heating, thinning, or mixing.

§  Compatible with various substrates and structures

§  Can be used at temperatures below 0°C 

Safety instructions

Bituprime Coating – P01 contains a flammable, toxic solvent. Always work in a ventilated area. Do not breathe in vapors.  Avoid exposing the product to any ignition sources.  Do not smoke when working with Bituprime Coating. It is advisable to wear gloves and safety glasses to avoid direct contact with skin or eyes.  If the product comes into contact with skin or eyes, rinse thoroughly and immediately with water.    Seek medical attention if irritation or discomfort persists. Protect from sunlight and do not expose to temperatures exceeding 40°C. Keep out of reach of children!  Refer to our Safety Data Sheet for further toxicological information and comprehensive handling instructions.

Storage:

Store in a dry place protected against sunlight at a temperature between -20°C and +30°C. Shelf life is 18 months.

Availability

Bituprime Coating – P01 is available in:

·        Bulk

·        IBC Tank, Flexi Tank

·        Reconditioned steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        New steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        20 Lit pails