Introduction of bitumen emulsion SS60

BACCO bitumen emulsion SS60 is a mixture of water & bitumen, Addition of an emulsifier with water facilitates the breaking of bitumen into minute particles, SS60 is an anionic (slow setting) road emulsion that contains 60% bitumen.

Asphalt emulsion SS60 is in chocolate brown in color and is a free-flowing liquid at ambient temperature and it is cold applied, liquid bitumen emulsions.

 

 

Typical properties of Bitumen emulsion SS60

BACCO SS60 bitumen emulsion is made according to the SANS 4001-BT3 standard.

 

EMULSION PROPERTIES	REQUIREMENT		TEST METHOD
	Min	Max
Binder content, % m/m	60	62	ASTM D244
Residue on sieving, g/100 ml	-	0.25	SANS 4001-BT3
Sedimentation after 60 rotations	Nil		SANS 4001-BT3
Coagulation value when mixed with cement, % m/m	-	2	SANS 4001-BT3

 

 

Advantages

At the following you can find some advantages of this product:

·        Environment friendly

·        No heating required

·        Cost efficient

·        Easy and uniform spray

·        Low-temperature curing, fast setting time

·        High adhesive properties

·        Prevents slippage of structural layers

 

Applications

SS 60 stable grade is used mainly as a cold-applied binder for the manufacture of slow-set slurry mixtures which can be batch-mixed and applied by hand or with a continuous mix and lay machine.

SS 60 stable grade can also be diluted with water and applied onto aged seals as an enrichment spray or tack coat for an asphalt overlay.

 The slow-setting nature of SS 60 stable grade makes it ideal for mixing and applying slurries by hand. Slurry mixtures prepared by batch mixing can be kept workable in transit mixers for up to 2 hours before setting.

 

Recommended rate of application

Bitumen Emulsion SS60 is designed for slurry seals and cold storable mixtures for patching. They are designed for soil stabilization and are also suitable for use with cold recycling. These emulsions are tailor-made as per the quality of aggregates and local site conditions.

 

Application	Quantity in Kg/10 m2 Area
Fog Seal	5 to 10
Slurry Seal	10 to 12
Premix Seal Coat	12 o 15

 

·        SS 60 stable grade can be stored and mixed with aggregates at ambient temperature.

·        Can be stored for up to six months at ambient temperature without risk of settlement.

·        As an enrichment spray or tack coat for HMA applications, the SS 60 stable grade should be diluted with water at a ratio of 1:1.

·        If diluting with water, confirm the compatibility of the water with the emulsion.

·        The binder should be heated to 60°C for spray applications.

·        As an enrichment spray, an application rate of 1,0 lt of diluted emulsion per m2 is recommended.

·        As a tack coat for HMA applications, an application rate of 0,5 lt of diluted emulsion per m2 is recommended.

 

To Ensure Best Result

·        Use without diluting Bitumen Emulsion with water

·        Use at ambient temperature

·        Roll the Bitumen Emulsion drums to and from motion at a distance of a minimum 5-meter

 

 

 

Handling and safety

·        Contains petroleum distillate; flammable: keep away from open fire, sparks, or other ignition sources; wear protective clothing, gloves, and goggles.

·        Fire flammable when wet, flash point 40°C.

·        Skin –avoid repeated or prolonged contact, if this occurs remove with hand cleaner that removes oil or grease, then clean with soap and water.

·        Eyes contact could cause irritation, if contact occurs flush immediately with clean water.

·        Inhalation can cause dizziness, move immediately in fresh air if dizzy and if breathing difficulty persists administer oxygen.

 

 

Cleaning

Tools: Clean with kerosene.

Hands: Use a hand cleanser or kerosene followed by soap and water.

 

Availability

BACCO Bitumen Emulsion SS60 is available in:

·        Bulk

·        IBC Tank, Flexi Tank

·        Reconditioned steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        New steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        20 lit pails

---

Introduction of bitumen emulsion SS-1h

BACCO bitumen emulsion SS-1h is an anionic slow-setting asphalt emulsion containing a minimum of 57% Bitumen designed for use as a tack coat, in fine-graded mixes, dust control, fog seal, and specialty applications. It is formulated with a harder base (lower penetration) than SS-1h for use in warmer climates.
SS-1h is a slow-setting anionic asphalt emulsion (i.e., low reactivity) low viscosity, and a hard asphalt residue that is designed for various paving and industrial uses. SS-1h Asphalt Binder is an anionic asphalt emulsion designed for use as a tack coat for patching, paving, and coating processes. SS-1h Asphalt Binder promotes the adhesion of bituminous concrete products and coatings. SS-1h Asphalt Binder also meets the ISSA requirements for SS-1h. Asphalt emulsions are classified according to the electric charge that surrounds the emulsion’s asphalt particles (i.e. whether it is a cationic or an anionic emulsion) and how quickly the suspended asphalt particles separate from the surrounding water (“breaking”). A slow-setting emulsion is designed to maximize the mixing time with aggregates.

 

 

Typical properties of Bitumen emulsion SS60

BACCO SS-1h bitumen emulsion is manufactured strictly as per ASTM D2397-13
AASHTO M208-16 or IS 8887: 2004.

PROPERTY	MIN	MAX	TEST METHOD
Viscosity SSF, 25 °C (s)	20	100	ASTM D244
Viscosity SSF, 50 °C (s)	—	—	ASTM D244
Storage stability, 24h (%)	—	1	ASTM D6930
Demulcibility  , 0.02 N CaCl2 (%)	—	—
Cement mixing (%)	—	2
Sieve (%)	—	0.1	ASTM D6933
Residue (%)	57		ASTM-D244
Solubility in trichloroethylene %	97.5		ASTM D2042
Penetration 77°F (25°C) 100g,5s mm	40	90	ASTM D5
ductility, 77°F (25 °C), 5cm/min (cm)	40		ASTM D113

 

Advantages

At the following you can find some advantages of this product:

·        Environment friendly

·        No heating required

·        Cost efficient

·        Easy and uniform spray

·        Low-temperature curing, fast setting time

·        High adhesive properties

·        Prevents slippage of structural layers

 

Applications

Anionic emulsion is obtained by an electric field. In an anionic emulsion, the droplets migrate from the anode. Anionic bitumen emulsion SS-1 is a slow-setting, anionic type of bitumen. The particle size of the emulsion is 0.1 to 5 microns and the emulsifier which is usually used for producing anionic Asphalt Emulsion SS-1 is alkaline salt with Ammonium Salt which puts the bitumen and water droplet together.

The main applications of Anionic bitumen emulsion SS-1 are waterproofing, building application, highway construction, surfacing, and maintenance.

SS-1h emulsions are used for a variety of purposes. Slow-setting emulsions are the most stable of emulsions and generally can be diluted with water and mixed with mineral fillers and aggregates for all paving uses, the air and pavement temperatures at construction should be sufficiently high to allow the emulsion to fully cure.

 

Recommended rate of application

Bitumen Emulsion SS-1h is designed for slurry seals and cold storable mixtures for patching. They are designed for soil stabilization and are also suitable for use with cold recycling. These emulsions are tailor-made as per the quality of aggregates and local site conditions.

 

Application	Quantity in Kg/10 m2 Area
Fog Seal	5 to 10
Slurry Seal	10 to 12
Premix Seal Coat	12 o 15

 

·        SS -1h stable grade can be stored and mixed with aggregates at ambient temperature.

·        Can be stored for up to six months at ambient temperature without risk of settlement.

·        As an enrichment spray or tack coat for HMA applications, the SS 60 stable grade should be diluted with water at a ratio of 1:1.

·        If diluting with water, confirm the compatibility of the water with the emulsion.

·        The binder should be heated to 60°C for spray applications.

·        As an enrichment spray, an application rate of 1,0 lt of diluted emulsion per m2 is recommended.

·        As a tack coat for HMA applications, an application rate of 0,5 lt of diluted emulsion per m2 is recommended.

 

To Ensure Best Result

·        Use without diluting Bitumen Emulsion with water

·        Use at ambient temperature

·        Roll the Bitumen Emulsion drums to and from motion at a distance of a minimum 5-meter

 

 

Handling and safety

·        Contains petroleum distillate; flammable: keep away from open fire, sparks, or other ignition sources; wear protective clothing, gloves, and goggles.

·        Fire flammable when wet, flash point 40°C.

·        Skin –avoid repeated or prolonged contact, if this occurs remove with hand cleaner that removes oil or grease, then clean with soap and water.

·        Eyes contact could cause irritation, if contact occurs flush immediately with clean water.

·        Inhalation can cause dizziness, move immediately in fresh air if dizzy and if breathing difficulty persists administer oxygen.

 

 

Cleaning

Tools: Clean with kerosene.

Hands: Use a hand cleanser or kerosene followed by soap and water.

 

 

Availability

BACCO Bitumen Emulsion SS-1h is available in:

·        Bulk

·        IBC Tank, Flexi Tank

·        Reconditioned steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        New steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        20 lit pails

 

---

Introduction of bitumen emulsion SS-1

BACCO bitumen emulsion SS-1 is an anionic slow-setting asphalt emulsion containing a minimum of 57% Bitumen designed for use as a tack coat, in fine-graded mixes, dust control, fog seal, and specialty applications.
SS-1 is a slow-setting anionic asphalt emulsion (i.e., low reactivity) low viscosity, and a hard asphalt residue that is designed for various paving and industrial uses. Asphalt emulsions are classified according to the electric charge that surrounds the emulsion’s asphalt particles (i.e. whether it is a cationic or an anionic emulsion) and how quickly the suspended asphalt particles separate from the surrounding water (“breaking”). A slow-setting emulsion is designed to maximize the mixing time with aggregates.
Longer workability times ensure a good coating on dense-graded aggregates with a high fine content. The setting speed of any emulsion is relative to atmospheric conditions at the time of construction.

 

Properties of Bitumen emulsion SS-1

BACCO SS-1 bitumen emulsion is manufactured strictly as per ASTM D2397-13
AASHTO M208-16 or IS 8887: 2004.

 

 

Advantages

At the following you can find some advantages of this product:

·        Environment friendly

·        No heating required

·        Cost efficient

·        Easy and uniform spray

·        Low-temperature curing, fast setting time

·        High adhesive properties

·        Prevents slippage of structural layers

 

Applications

Anionic emulsion is obtained by an electric field. In an anionic emulsion, the droplets migrate from the anode. Anionic bitumen emulsion SS-1 is a slow-setting, anionic type of bitumen. The particle size of the emulsion is 0.1 to 5 microns and the emulsifier which is usually used for producing anionic Asphalt Emulsion SS-1 is alkaline salt with Ammonium Salt which puts the bitumen and water droplet together.

The main applications of Anionic bitumen emulsion SS-1 are waterproofing, building application, highway construction, surfacing, and maintenance.

SS-1h emulsions are used for a variety of purposes. Slow-setting emulsions are the most stable of emulsions and generally can be diluted with water and mixed with mineral fillers and aggregates for all paving uses, the air and pavement temperatures at construction should be sufficiently high to allow the emulsion to fully cure.

 

Recommended rate of application

Bitumen Emulsion SS-1 is designed for slurry seals and cold storable mixtures for patching. They are designed for soil stabilization and are also suitable for use with cold recycling. These emulsions are tailor-made as per the quality of aggregates and local site conditions.

 

Application	Quantity in Kg/10 m2 Area
Fog Seal	5 to 10
Slurry Seal	10 to 12
Premix Seal Coat	12 o 15

 

 

·        May be further diluted with potable water

·        Do not apply if precipitation is anticipated.

·        Do not dilute the product with any cutter stock.

 

 

To Ensure Best Result

·        Use without diluting Bitumen Emulsion with water

·        Use at ambient temperature

·        Roll the Bitumen Emulsion drums to and from motion at a distance of a minimum 5-meter

 

 

Handling and safety

·        Contains petroleum distillate; flammable: keep away from open fire, sparks, or other ignition sources; wear protective clothing, gloves, and goggles.

·        Fire flammable when wet, flash point 40°C.

·        Skin –avoid repeated or prolonged contact, if this occurs remove with hand cleaner that removes oil or grease, then clean with soap and water.

·        Eyes contact could cause irritation, if contact occurs flush immediately with clean water.

·        Inhalation can cause dizziness, move immediately in fresh air if dizzy and if breathing difficulty persists administer oxygen.

 

 

Cleaning

Tools: Clean with kerosene.

Hands: Use a hand cleanser or kerosene followed by soap and water.

 

Availability

BACCO Bitumen Emulsion SS-1 is available in:

·        Bulk

·        IBC Tank, Flexi Tank

·        Reconditioned steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        New steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        20 lit pails

---

 

 

---

 

·     Bulk

·     IBC Tank, Flexi Tank

·     Reconditioned steel drums 220 lit., Net Weight: 200 ± 3 Kg

·     New steel drums 220 lit., Net Weight: 200 ± 3 Kg

20 lit pail

---

Introduction of bitumen emulsion MS-2

BACCO bitumen emulsion MS-2 is an anionic water-based emulsified asphalt with moderate viscosity and setting time containing a minimum of 60% bitumen designed to make it an ideal product for premixing applications. It is chocolate brown in color and is a free-flowing liquid at ambient temperature

 

 

Typical properties of Bitumen emulsion MS-2

BACCO MS-2 bitumen emulsion is manufactured strictly as per ASTM D2397-13
AASHTO M208-16 or IS 8887: 2004.

 

 

 

Advantages

At the following you can find some advantages of this product:

·        Environment friendly

·        No heating required

·        Cost efficient

·        Easy and uniform spray

·        Low-temperature curing, fast setting time

·        High adhesive properties

·        Prevents slippage of structural layers

Applications

Bitumen Emulsion MS-2 is ideally suited for

• Pothole repair/ Patchwork
• 20mm Pre-Mix Carpet
• cold mix treatment

 

Recommended rate of application

Bitumen Emulsion MS-2 for preparation of mix is 7% by weight of aggregates

 

 

To Ensure Best Result

·        Use without diluting Bitumen Emulsion with water

·        Use at ambient temperature

·        Roll the Bitumen Emulsion drums to and from motion at a distance of a minimum of 5 meter

 

Handling and safety

·        Contains petroleum distillate; flammable: keep away from open fire, sparks, or other ignition sources; wear protective clothing, gloves, and goggles.

·        Fire flammable when wet, flash point 40°C.

·        Skin –avoid repeated or prolonged contact, if this occurs remove with hand cleaner that removes oil or grease, then clean with soap and water.

·        Eyes contact could cause irritation, if contact occurs flush immediately with clean water.

·        Inhalation can cause dizziness, move immediately in fresh air if dizzy and if breathing difficulty persists administer oxygen.

 

Cleaning

Tools: Clean with kerosene.

Hands: Use a hand cleanser or kerosene followed by soap and water.

 

Availability

BACCO Bitumen Emulsion MS-2 is available in:

·        Bulk

·        IBC Tank, Flexi Tank

·        Reconditioned steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        New steel drums 220 lit., Net Weight: 200 ± 3 Kg

20 lit pails

---

Introduction of bitumen emulsion K3

BACCO bitumen emulsion K3 is a mixture of water & bitumen, The addition of an emulsifier with water facilitates the breaking of bitumen into minute particles, K3 is a cationic (slow setting) road emulsion that contains 56% bitumen.

Asphalt emulsion K3 is in chocolate brown in color and is a free-flowing liquid at ambient temperature and it is cold applied, liquid bitumen emulsions.

 

 

Typical properties of Bitumen emulsion K3

BACCO K3 cationic bitumen emulsion is made according to KS 02-769: 1990 standard.

 

 

 

Advantages

At the following you can find some advantages of this product:

·        Environment friendly

·        No heating required

·        Cost efficient

·        Easy and uniform spray

·        Low-temperature curing, fast setting time

·        High adhesive properties

·        Prevents slippage of structural layers

 

Applications

Bitumen Emulsion K3 is for road pavement bases and surface projects such as:

·        Plant mix (cold) with both dense-graded aggregate and sand

·        Mixed-in-place with dense-graded aggregate

·        Slurry seal

Also, k3 emulsified bitumen is used for some bituminous applications like:

·        Fog Seal

·        Prime coat-penetrable surface

·        Tack coat

·        Dust Binder

·        Mulch Treatment

·        Crack filler

 

Recommended rate of application

Bitumen Emulsion K3 is designed for slurry seals and cold storable mixtures for patching. They are designed for soil stabilization and are also suitable for use with cold recycling. These emulsions are tailor-made as per the quality of aggregates and local site conditions.

 

 

 

To Ensure Best Result

·        Use without diluting Bitumen Emulsion with water

·        Use at ambient temperature

·        Roll the Bitumen Emulsion drums to and from motion at a distance of a minimum 5-meter

 

 

Handling and safety

·        Contains petroleum distillate; flammable: keep away from open fire, sparks, or other ignition sources; wear protective clothing, gloves, and goggles.

·        Fire flammable when wet, flash point 40°C.

·        Skin –avoid repeated or prolonged contact, if this occurs remove with hand cleaner that removes oil or grease, then clean with soap and water.

·        Eyes contact could cause irritation, if contact occurs flush immediately with clean water.

·        Inhalation can cause dizziness, move immediately in fresh air if dizzy and if breathing difficulty persists administer oxygen.

Cleaning

Tools: Clean with kerosene.

Hands: Use a hand cleanser or kerosene followed by soap and water.

 

Availability

BACCO Bitumen Emulsion K3 is available in:

·        Bulk

·        IBC Tank, Flexi Tank

·        Reconditioned steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        New steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        20 lit pails

---

Introduction of bitumen emulsion K2

BACCO bitumen emulsion K2 is a cationic emulsion that contains 57% bitumen. In fact, K2 is a cationic medium setting emulsion as per British standards and it’s suitable for premix – carpet and pothole repair.

Asphalt emulsion K2 is in chocolate brown in color and is a free-flowing liquid at ambient temperature it is cold-applied, liquid bitumen emulsions, used in the construction and repair of pavements, driveways, roads, and highways.

 

Typical properties of bitumen emulsion K2

BACCO K2 cationic bitumen emulsion is made according to KS 02-769: 1990 standard.

 

 

 

Advantages

At the following you can find some advantages of this product:

·        Environment friendly

·        No heating required

·        Cost efficient

·        Easy and uniform spray

·        Low-temperature curing, fast setting time

·        High adhesive properties

·        Prevents slippage of structural layers

 

Applications

Emulsified emulsion K2 is used for pavement bases and surfaces as:

·        Plant mix (cold) with open-graded aggregate

·        Mixed-in-place with open-graded aggregate

Also, Bitumen Emulsion K2 is primarily used as a tack coat, to provide a bond between the existing surface and overlays e.g. hot rolled asphalt, macadam, and slurry seals, or between courses in road construction.

The typical rate of application of BACCO Bitumen Emulsion K2 for Patch Repairing/Pot Hole Repairing is 7 % by weight of aggregates.

Tack Coat K2 cationic bitumen emulsion can be used at ambient temperature at the spray rate of 0.25 to 0.70 liter per square meter (0.05 to 0.15 gallon per square yard).

 

To Ensure Best Result

·        Use without diluting Bitumen Emulsion with water

·        Use at ambient temperature

·        Roll the Bitumen Emulsion drums to and from motion at a distance of a minimum 5-meter

 

 

 

Handling and safety

·        Contains petroleum distillate; flammable: keep away from open fire, sparks, or other ignition sources; wear protective clothing, gloves, and goggles.

·        Fire flammable when wet, flash point 40°C.

·        Skin –avoid repeated or prolonged contact, if this occurs remove with hand cleaner that removes oil or grease, then clean with soap and water.

·        Eyes contact could cause irritation, if contact occurs flush immediately with clean water.

·        Inhalation can cause dizziness, move immediately in fresh air if dizzy and if breathing difficulty persists administer oxygen.

 

 

Cleaning

Tools: Clean with kerosene.

Hands: Use a hand cleanser or kerosene followed by soap and water.

 

 

 

Availability

BACCO Bitumen Emulsion K2 is available in:

·        Bulk

·        IBC Tank, Flexi Tank

·        Reconditioned steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        New steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        20 lit pails

---

Introduction of bitumen emulsion K1-70

BACCO asphalt emulsion K1-70 is a cationic rapid-setting bitumen emulsion that contains 67% bitumen. It is a medium viscosity emulsion used mainly for tack coating in normal overlay and patching work. Bitumen emulsion K1-700 is chocolate brown in color and is a free-flowing liquid at ambient temperature and is commonly used for Tack-Coating as well.

 

 

 

Typical properties of Bitumen emulsion K1-70

BACCO K1-70 cationic bitumen emulsion is made according to KS 02-769: 1990 standard and Malaysian Standard, MS 1.61 (1994).

 

 

 

 

 

 

 

 

Advantages

At the following you can find some advantages of this product:

·        Environment friendly

·        No heating required

·        Cost efficient

·        Easy and uniform spray

·        Low-temperature curing, fast setting time

·        High adhesive properties

·        Prevents slippage of structural layers

 

Applications

Bitumen Emulsion K1-70 is primarily used as a tack coat, to provide a bond between the existing surface and overlays e.g. hot rolled asphalt, macadam, and slurry seals, or between courses in road construction.

Also, one of the main applications of emulsion K1-70 is in road surface treatments and seals:

·        Single surface treatment

·        Multiple surface treatment

·        Sand seal

Tack Coat K1-70 cationic bitumen emulsion can be used at ambient temperature at the spray rate of 0.25 to 0.70 liter per square meter (0.05 to 0.15 gallon per square yard).

The typical rate of application K1-70 for two coats of surface dressing as per (MORTH&H) clause 510.2 is   28-32 kg/10sq.m.

 

To Ensure Best Result

·        Use without diluting Bitumen Emulsion with water

·        Use at ambient temperature

·        Roll the Bitumen Emulsion drums to and from motion at a distance of a minimum 5-meter

 

 

Handling and safety

·        Contains petroleum distillate; flammable: keep away from open fire, sparks, or other ignition sources; wear protective clothing, gloves, and goggles.

·        Fire flammable when wet, flash point 40°C.

·        Skin –avoid repeated or prolonged contact, if this occurs remove with hand cleaner that removes oil or grease, then clean with soap and water.

·        Eyes contact could cause irritation, if contact occurs flush immediately with clean water.

·        Inhalation can cause dizziness, move immediately in fresh air if dizzy and if breathing difficulty persists administer oxygen.

Cleaning

Tools: Clean with kerosene.

Hands: Use a hand cleanser or kerosene followed by soap and water.

 

Availability

BACCO Bitumen Emulsion K1-70 is available in:

·        Bulk

·        IBC Tank, Flexi Tank

·        Reconditioned steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        New steel drums 220 lit., Net Weight: 200 ± 3 Kg

·        20 lit pails

---