Introduction of cutback bitumen MC250
BACCO Bitumen MC250 is medium curing (MC) cut-back asphalt consisting of penetration grade asphalt cement and diluent or cutter of medium volatility. The diluent temporarily reduces the viscosity of the asphalt cement for ease of handling and application. After application, the diluent evaporates, leaving asphalt cement to perform its function. MC–250 bitumen viscosity is between 250-500 CST. Cutback bitumen MC-250 is dissolved bitumen in the solvents of kerosene.
Typical properties
|
Characteristic |
Value |
Test Method |
|
Kinematic Viscosity@ 60°C (cSt) |
250-500 |
ASTM D-2170 |
|
Flash Point (top open cuo) (°C) |
66 min |
ASTM D-3143 |
|
Water Content (%vol) |
0.2 max |
ASTM D-95 |
|
Distillate, %volume of total distillate to @ 360°C: |
||
|
to 225°C |
10 max |
ASTM D-402 |
|
to 260°C |
15-55 |
|
|
to 316°C |
60-87 |
|
|
Residue from Distillation to 360°C (%Vol by difference) |
67 min |
ASTM D-402 |
|
Test on Residue from Distillation |
||
|
Penetration @ 25°C (DMM) |
120-250 |
ASTM D-5 |
|
Ductility @ 25°C (cm) |
100 min |
ASTM D-113 |
|
solubility in Trichloroethylene (%wt) |
99 min |
ASTM D-2042 |
Applications
This kind of bitumen is suitable to be used in the construction and treatment of pavements as per ASTM D2028-97 reapproved in 2004. Cutback-grade bitumen is normally used in spraying and in some mixing applications.
Hazard Identification
NOT classified as dangerous in accordance with Directive 67/548/EEC or EC 1272/2008.
The main hazards presented by Asphalt relate to the temperature of the material. The following hazards may apply:
- Hot materials may burn the skin.
- Fumes from Asphalt are unlikely to be hazardous when laid in open-air situations, but there may be a risk to health by continuous inhalation of high vapor concentrations which might arise in poorly ventilated, confined, or semi-confined spaces.
- Asphalt is not a dusty material, but respirable dust may be released by cutting, drilling, or planning hardened asphalt. If inhaled in excessive quantities over a prolonged period or extended period, respirable dust can constitute a long-term health hazard.
Dusts containing Respirable Crystalline Silica* (quartz) present a greater hazard. Long-term exposure to respirable dust can lead to respiratory system damage and disease. Respirable crystalline silica* has been associated with the lung disease silicosis.
The quartz content of the product will vary and is related to the type of aggregate used in the production of the asphalt. Advice on the quartz content and other chemical information is available from the supplying unit.
Fire Fighting Measures
Suitable Extinguishing Media: Dry powder, foam.
Unsuitable Extinguishing Media: Do not use water. CO2 is also not suitable.
Special Exposure Hazards in Fire: Hydrocarbon fumes may be released, along with other hazardous combustion products including smoke.
Special Protective Equipment for Fire Fighters: Proper protective equipment including suitable respirators or breathing apparatus must be worn.
Handling and Storage
Handling:
Skin contact with the product should be avoided. Inhalation of fumes should be avoided as far as is reasonably practicable.
If the formation of vapors is a risk, then additional ventilation should be provided. Handle away from sources of ignition and heat. Do not smoke, eat or drink during use.
Storage
No special requirements. Asphalt is normally used upon receipt.
Refer to the relevant Technical Data Sheet for the specific product.
Cleaning
Tools: Clean with kerosene and gasoline.
Hands: Use a hand cleanser or kerosene followed by soap and water.
Availability
BACCO Bitumen MC250 is available in: Bulk and New Steel Drums (185 Kg)